DID YOU KNOW?


FEDERAL MANDATED REGULATIONS
REQUIRE THAT VEHICLES TRADED IN VIA
THE GOVERNMENT C.A.R.S. STIMULUS
(CASH FOR CLUNKERS)
PROGRAM ARE REQUIRED TO HAVE THE
ENGINES DISABLED.


ATTACHED IS THE FEDERAL GUIDELINE FOR ENGINE
DISABLEMENT PROCEDURES FOR THE C.A.R.S.
PROGRAM.


IRONTITE HAS A PRODUCT THAT MEETS THE
GOVERNMENT'S REQUIREMENTS FOR ENGINE
DISABLEMENT UNDER THIS PROGRAM.

With our many years of experience making premium products for the
Automotive Industry, you can rest assured that our Engine Disablement Solution
will perform with the least hassle and best results!


UNDER THE CONSUMER ASSISTANCE TO RECYCLE AND SAVE (C.A.R.S.) PROGRAM, DEALERS
ARE REQUIRED TO DISABLE THE ENGINE OF THE VEHICLE TAKEN IN ON TRADE FOR WHICH A
C.A.R.S. REBATE IS RECEIVED.

IRONTITE ENGINE DISABLEMENT SOLUTION, Part Number 9140-01, HAS THE
CHEMICAL COMPOSITION THAT CONFORMS TO Appendix B to Part
599 OF THE FEDERAL REGULATIONS AND IS GUARANTEED TO
DISABLE AN ENGINE WHEN CIRCULATED IN PLACE OF THE OIL.

CALL YOUR DISTRIBUTOR TODAY
OR CALL 800-553-5953 7:30am - 5:00pm CST

FOR A DISTRIBUTOR NEAR YOU
Irontite by Kwik-Way, 500 57th Street, Marion, IA 52302
Appendix B to Part 599 - Engine Disablement Procedures for the CARS

Engine Disablement Procedures for the CARS Program
THIS PROCEDURE IS NOT TO BE USED BY THE VEHICLE OWNER

Perform the following procedure to disable the vehicle engine.
  1. Obtain solution of 40% sodium silicate/60% water. (The Sodium Silicate (SiO2/Na2O) must have a weight ratio of 3.0 or greater.)
  2. Drain engine oil for environmentally appropriate disposal.
  3. Install the oil drain plug.
  4. Since the procedure is intended to render the engine inoperative, drive or move the vehicle to the desired area for disablement.
  5. Pour enough solution in the engine through the oil fill for the oil pump to circulate the solution throughout the engine. Start by adding 2 quarts of the solution, which should be sufficient in most cases.
  6. CAUTION: Wear goggles and gloves. Appropriate protective clothing should be worn to prevent silicate solution from coming into contact with the skin.
  7. Replace the oil fill cap.
  8. Start the engine.
  9. Run engine at approximately 2000 rpm (for safety reasons do not operate at high rpm) until the engine stops.Typically the engine will operate for 3 to 7 minutes. As the solution starts to affect engine operation, the operator will have to apply more throttle to keep the engine at 2000 rpm.)
  10. Allow the engine to cool for at least 1 hour.
  11. With the battery at full charge or with auxiliary power to provide the power of a fully charged battery, attempt to start the engine.
  12. If the engine will not operate at idle, the procedure is complete.
  13. If the engine will operate at idle, repeat steps 7 through 11 until the engine will no longer idle.
  14. Attach a label to the engine that legibly states the following:
    This engine is from a vehicle that is part of the Car Allowance Rebate System (CARS). It has significant internal damage caused by operating the engine with a sodium silicate solution (liquid glass) instead of oil.
  15. File this document in the file for the new vehicle purchase.

From: DEPARTMENT OF TRANSPORTATION
National Highway Traffic Safety Administration,
49 DFR Parts 512 and 599
Docket No. NHTSA-2009-0120
RIN 2127-AK53
Requirements and Procedures for Consumer Assistance to Recycle and Save Program



Irontite Engine Disablement Solution (Sodium Silicate Solution)
Part Number 9140-01 (1 Gal.) or 9140-05 (5 Gal.)
meets the chemical requirements for Engine Disablement
under the Federal CARS program.

CALL YOUR DISTRIBUTOR TODAY
OR CALL 800-553-5953 7:30am - 5:00pm CST

FOR A DISTRIBUTOR NEAR YOU
Irontite by Kwik-Way,500 57th Street, Marion, Iowa 52302

Irontite by Kwik-Way 500 57th Street, Marion, IA 52302
319-377-9421, 319-377-9101 FAX